Publications

Selected

1. 2026
   S. Fulco, M.K. Budzik, K.T. TurnerArchitected interfaces: Tailoring toughness and adhesion through geometry, invited ’perspective’ article to npj Metamaterials, 2, 1-10.
2. 2026
   S. Fulco, P.K. Purohit, M.K. Budzik, K.T. TurnerFracture of disordered and stochastic lattice materials, Proc. R. Soc. A (accepted 21.04.2026) (preprint available through arXiv:2508.21187). accepted
3. 2025
   S. Fulco, H. Xiao, M.K. Budzik, D.J. Durian, K.T. TurnerDisorder enhances the fracture toughness of 2D mechanical metamaterials, PNAS Nexus 4(2), pgaf023 (2025).
4. 2024
   Ch. Van Innis, M.K. Budzik, T. PardoenUltra tough, architected material joints for integrated composite processing and bonding, Comp. Part A 177, 107949 (2024).
5. 2024
   S. Fulco, M.K. Budzik, K.T. Turner, E.B. BainControlling process zone via geometry to enhance toughness, J. Mech. Phys. Solids, 105548 (2024).
6. 2022
   S. Fulco, M.K. Budzik, K.T. Turner, E.B. BainDecoupling toughness and strength through architected plasticity, Ext. Mech. Lett., 101912 (2022).
7. 2021
   A.E.F. Athanasiadis, M.A. Dias, M.K. BudzikCan confined mechanical metamaterials replace adhesives?, Ext. Mech. Lett. 48, 101411 (2021).
8. 2021
   R. Aghababaei, M. Malekan, M.K. BudzikCutting depth dictates transition from continuous to segmented chip formation, Phys. Rev. Lett. 127, 235502 (2021).
9. 2020
   S. Heide-Jørgensen, M.K. Budzik, K.T. TurnerMechanics and fracture of structured pillar interfaces, J. Mech. Phys. Solids 137, 103825 (2020).

All publications (102)

1. 2026
   M.K. Budzik, O. Duncan, M.A. Dias, L. Peel, K. Alderson, F. ScarpaAuxetic fibre-polymer composites in Roadmap on Mechanical Metamaterials (ed. O. Duncan, M.A. Dias, A. Alderson), revision, Smart Materials and Structures, IOP Science, 16.05.2025. revision
2. 2026
   S. Fulco, M.K. Budzik, K.T. TurnerArchitected interfaces: Tailoring toughness and adhesion through geometry, invited ’perspective’ article to npj Metamaterials, 2, 1-10.
3. 2026
   S. Fulco, P.K. Purohit, M.K. Budzik, K.T. TurnerFracture of disordered and stochastic lattice materials, Proc. R. Soc. A (accepted 21.04.2026) (preprint available through arXiv:2508.21187). accepted
4. 2026
   P. Hu, M.K. BudzikDesigned intermittency in interlaminar fracture via kirigami-induced crack-front widening, Comp. Sci. Technol. 279, 111611 (2026).
5. 2026
   S.S. Wahlgren, H. Myhre Jensen, M.K. BudzikOn the transition from arc debonding to tunneling at fiber-matrix interfaces, Comp. Part B, 113624 (2026).
6. 2026
   P. Nguyen, S. Wahlgren, S. Peder Madsen, M.K. BudzikSegmented rim design for high performance flywheel energy storage system, Energ. Rep. (submitted 17.12.2025). submitted
7. 2026
   C.K. Kristensen, J. Kirkegaard, J. Hesselvig, C.G. Sanporean, M.K. Budzik, M. SandbergPredictive and numerical modelling of discoloration and its correlation with mechanical and dimensional properties of PA11 SLS parts, Addit. Manuf. (submitted 14.01.2026). submitted
8. 2026
   M. Mieloszyk, M.K. Budzik (editors)Non Destructive Testing and Structural Health Monitoring in Additively Manufactured Polymers, Elsevier, 2026, in preparation. Book chapter in preparation
9. 2025
   Ch. Van Innis, M.K. Budzik, T. PardoenBridging in co-cured composite joints, Int. J. Solids Struct. 309, 113194 (2025).
10. 2025
    S. Fulco, H. Xiao, M.K. Budzik, D.J. Durian, K.T. TurnerDisorder enhances the fracture toughness of 2D mechanical metamaterials, PNAS Nexus 4(2), pgaf023 (2025).
11. 2025
    P. Hu, S. Li, M.K. BudzikDecoupling fracture energy from crack area via surface patterning, Surf. Interfaces 62, 106066 (2025).
12. 2025
    A.E.F. Athanasiadis, O. Duncan, M.K. Budzik, M.A. DiasToughness of Confined Auxetic Foams, Adv. Eng. Mater. 2500626 (2025).
13. 2025
    J. Hasselvig, R.T. Nygaard, M.K. Budzik, M. SandbergEfficient continuum-based modelling and analysis of polymer SLS: Insights into particle sintering and densification in straight and corner scanning passes, Addit. Manuf. 109, 104828 (2025).
14. 2025
    A. Taylor, G. Saurya Vankayalapati, M.K. Budzik, K.T. TurnerHinged Rigid Beam fracture specimen for characterization of lattice and thin-sheet materials, Exp. Mech. 65, 1375–1386 (2025) - article featured on the cover.
15. 2024
    M. Hedvard, M.A. Dias, M.K. BudzikToughening mechanisms and damage propagation in Architected-Interfaces, Int. J. Sol. Struct. 288, 112600 (2024).
16. 2024
    Ch. Van Innis, M.K. Budzik, T. PardoenUltra tough, architected material joints for integrated composite processing and bonding, Comp. Part A 177, 107949 (2024).
17. 2024
    S. Fulco, M.K. Budzik, K.T. Turner, E.B. BainControlling process zone via geometry to enhance toughness, J. Mech. Phys. Solids, 105548 (2024).
18. 2024
    A.E.F. Athanasiadis, M.K. Budzik, D. Fernando, M.A. DiasOn Micropolar Elastic Foundations, Eur. J. Mech. A., 105277 (2024).
19. 2024
    B.U. Bokharaie, R. Aghababaei, M.A. Dias, M.K. BudzikFailure of 3D-Printed Composite Continuous Carbon Fiber Hexagonal Frames, Comp. Part B 275, 111307 (2024).
20. 2024
    J. Airao, M. Malekan, M.K. Budzik, R. AghababaeiEffect of friction on critical cutting depth for ductile-brittle transition in material removal mechanism, Journal of Tribology 146(11) (2024).
21. 2024
    P. Hu, M.A. Dias, M.K. BudzikGeometric tunability of delamination resistance, Comp. Part B 287, 111839 (2024).
22. 2023
    S. Teixeira De Freitas, M.K. BudzikIn Advances in Structural Adhesive Bonding (2nd edition), Edited by David Dillard, Chapter 18: Bondline thickness: Fracture mechanics perspective, Woodhead (Elsevier), 2023, Pages 615–641. Book chapter
23. 2023
    T. Pardoen, K.T. Turner, M.K. BudzikIn Advances in Structural Adhesive Bonding (2nd edition), Edited by David Dillard, Chapter 34: Architected adhesive joints with improved fracture toughness, Woodhead (Elsevier), 2023, Pages 1105–1122. Book chapter
24. 2022
    S. Rao, M.K. Budzik, M.A. DiasOn microscopic fracture analysis of unidirectional composite material using Phase Field Modelling, Comp. Sci. Technol. 220, 109242 (2022).
25. 2022
    M. Nasr Saleh, M. Saeedifar, R. Lopes Fernandes, M.K. Budzik, D. Zarouchas, S. Teixeira De FreitasOn the influence of the adhesive and the adherend ductility on mode I fracture characterization of thick adhesively-bonded joints, Int. J. Adhes. Adhes. 115, 103123 (2022).
26. 2022
    S. Fulco, M.K. Budzik, K.T. Turner, E.B. BainDecoupling toughness and strength through architected plasticity, Ext. Mech. Lett., 101912 (2022).
27. 2022
    S. Heide-Jørgensen, M.K. Budzik, C. IbsenThree-dimensional, multiscale homogenization for hybrid woven composites with fiber-matrix debonding, Comp. Sci. Technol. 218, 109204 (2022).
28. 2021
    S. Heide-Jørgensen, M.K. Budzik, K. Birk Buhl, M. Hinge, S. Pedersen, K. Daasbjerg, M. KongsfeltMode I debonding under large deformation conditions including notes on cleavagepeeling transition, Eng. Fract. Mech. 241, 107413 (2021).
29. 2021
    S. Heide-Jørgensen, M.K. Budzik, C. IbsenEffective through-the-thickness diffusivity of plain-woven composite from analytical homogenization, Comp. Sci. Technol. 202, 108552 (2021).
30. 2021
    M. Malekan, M.K. Budzik, H. Myhre Jensen, R. AghababaeiFracture analyses of surface asperities during sliding contact, Trib. Intl. 159, 106939 (2021).
31. 2021
    R. Lopes Fernandes, M.K. Budzik, S. Teixeira de Freitas, R. BenedictusMulti-material adhesive joints with thick bond-lines: crack onset and crack deflection, Comp. Struct., 113687 (2021).
32. 2021
    M.K. Budzik, M. Wolfahrt, P. Reis, M. Kozłowski, J. Sena Cruz, L. Papadakis, M. Saleh, K.V. Machalicka, S. Teixeira de Freitas, A. VassilopoulosTesting mechanical performance of adhesively bonded composite joints in engineering applications: An overview, J. Adhes. (2021).
33. 2021
    M.K. Budzik, S. Heide-Jørgensen, R. AghababaeiFracture mechanics analysis of delamination along width-varying interfaces, Comp. Part B, 108793 (2021).
34. 2021
    J. Barbalić, V. Rajčić, Ch. Bedon, M.K. BudzikShort-term analysis of adhesive types and bonding mistakes on Bonded-in-Rod (BiR) connections for timber structures, Appl. Sci. 11, 2665 (2021).
35. 2021
    A.E.F. Athanasiadis, M.A. Dias, M.K. BudzikCan confined mechanical metamaterials replace adhesives?, Ext. Mech. Lett. 48, 101411 (2021).
36. 2021
    S. Heide-Jørgensen, C. Ibsen, M.K. BudzikTemperature dependence of moisture diffusion in woven epoxy-glass composites: A theoretical and experimental study, Materials Today Communications 29, 102844 (2021).
37. 2021
    R. Aghababaei, M. Malekan, M.K. BudzikCutting depth dictates transition from continuous to segmented chip formation, Phys. Rev. Lett. 127, 235502 (2021).
38. 2020
    R. Aghababaei, M.K. BudzikFracture modes of brittle junctions under shear, Ext. Mech. Lett., 100644 (2020).
39. 2020
    S. Heide-Jørgensen, M.K. Budzik, K.T. TurnerMechanics and fracture of structured pillar interfaces, J. Mech. Phys. Solids 137, 103825 (2020).
40. 2020
    K. Birk Buhl, Asger H. Agergaard, R. Krag Møller, M. Kongsfelt, S. Heide-Jørgensen, M.K. Budzik, M. Hinge, S. Pedersen, K. DaasbjergFacile access to disulfide/thiol containing poly(glycidyl methacrylate) brushes as potential rubber adhesive layers, ACS Appl. Poly. Mater. 2(6), 2380–2388 (2020).
41. 2020
    R. Lopes Fernandes, S. Teixeira de Freitas, M.K. Budzik, J.A. Poulis, R. BenedictusRole of adherend material on the fracture of bi-material composite bonded joints, Comp. Struct., 112643 (2020).
42. 2019
    R. Lopes Fernandes, S. Teixeira De Freitas, M.K. Budzik, J.A. Poulis, R. BenedictusFrom thin to extra-thick adhesive layer thicknesses: fracture of bonded joints under mode I loading conditions, Eng. Fract. Mech. 218, 106607 (2019).
43. 2018
    A. Møberg, M.K. Budzik, H. Myhre JensenGrowth from initial to self-similar shape of an interface crack front, Int. J. Adhes. Adhes. 83, 59–68 (2018).
44. 2018
    J. Jumel, M.K. BudzikInverse End-Loaded-Split Test Analysis: Effect of small-scale yielding, Theor. Appl. Fract. Mech. 96, 775–789 (2018).
45. 2018
    S. Heide-Jørgensen, M.K. Budzik, S. Teixeira De FreitasOn the fracture behaviour of CFRP bonded joints under mode I loading: Effect of supporting carrier and interface contamination, Comp. Sci. Technol. 160, 97–110 (2018).
46. 2018
    S. Heide-Jørgensen, M.K. BudzikEffects of bondline discontinuity during growth of interface cracks including stability and kinetic considerations, J. Mech. Phys. Solids 117, 1–21 (2018).
47. 2018
    M.K. Budzik, S. Heide-JørgensenBranching and softening of loading path during onset of crack at elastic-brittle interface, Mech. Mater. 127, 1–13 (2018).
48. 2018
    S. Heide-Jørgensen, K. Birk Buhl, R. Krag Møller, M.K. Budzik, M. Hinge, K. Daasbjerg, et al.Ultra-thin Nano-scaled Chemical Modification to Cohesive Strength between EPDM Rubber and Metal, Int. J. Adhes. Adhes. 87, 31–41 (2018).
49. 2018
    K. Birk Buhl, A. Kolding, R. Krag Møller, M. Kongsfelt, S. Heide-Jørgensen, M.K. Budzik, M. Hinge, S. Pedersen, K. DaasbjergHighly efficient rubber-to-stainless steel bonding by nanometer-thin cross-linked polymer brushes, ACS Omega 3(12), 17511–17519 (2018).
50. 2017
    G. Strugala, M. Landowski, M.K. Budzik, K. ImielińskaImpact damage in SiO2 nanoparticle enhanced epoxy-carbon fibre composites, Comp. Part B: Eng. 113, 91–99 (2017).
51. 2017
    S. Heide-Jørgensen, M.K. BudzikCrack growth along heterogeneous interface during the DCB experiment, Int. J. Sol. Struct. 120, 278–291 (2017).
52. 2017
    A. Møberg, M.K. Budzik, H. Myhre JensenCrack front morphology near the free edges in double and single cantilever beam fracture experiments, Eng. Fract. Mech. 175, 219–234 (2017).
53. 2017
    M.K. Budzik, J. JumelInverse End Loaded Split test configuration for stable Mode II crack propagation in bonded joint: Macroscopic analysis – Effective crack length approach, Int. J. Fract. 207(1), 27–39 (2017).
54. 2016
    M.K. Budzik, H. Myhre JensenEvaluation of defects during double cantilever beam experiment on adhesive joint, Key Eng. Mat. 665, 101–104 (2016).
55. 2016
    M.K. Budzik, H. Myhre JensenExperimental study of cracks at interfaces with voids, Procedia Structural Integrity 2, 277–284 (2016).
56. 2015
    M.K. Budzik, H. Myhre JensenFracture in the single cantilever beam test with large scale bridging, Key Eng. Mat. 627, 221–224 (2015).
57. 2015
    A. Møberg, M.K. Budzik, H. Myhre JensenIntersection of the interface crack front with free edge, Key Eng. Mat. 627, 225–228 (2015).
58. 2015
    J. Jumel, N. Ben Salem, M.K. Budzik, M.E.R. ShanahanMeasurement of interface cohesive stresses and strains evolutions with combined mixed mode crack propagation test and backface strain monitoring measurements, Int. J. Sol. Struct. 52, 33–44 (2015).
59. 2015
    W. Possart, J. Jumel, M.K. Budzik, J. Guitard, M.E.R. ShanahanExperimental study of cohesive strain prior to crack initiation in constant force single cantilever beam test, J. Adhes. Sci. Technol. 29(9), 896–909 (2015).
60. 2014
    M.K. Budzik, J. Jumel, N. Ben Salem, M.E.R. ShanahanComparison of Cyclic and Monotonic Loading of a Double Cantilever Beam Adhesion Test, J. Adhesion 90(3), 252–267 (2014).
61. 2014
    M.K. Budzik, J. Jumel, M.E.R. ShanahanExperimental investigation of a crack front triple line, Appl. Phys. B 114(2), 495–501 (2014).
62. 2014
    M.K. Budzik, H. Myhre JensenBonded bimaterial ring under load, Proc. I. Mech. Eng. Part L: Journal of Materials: Design and Application 228(3), 100–108 (2014).
63. 2014
    M.K. Budzik, H. Myhre JensenPerturbation analysis of crack front in simple cantilever plate peeling experiment, Int. J. Adhes. Adhes. 53, 29–33 (2014).
64. 2014
    N. Ben Salem, J. Jumel, M.K. Budzik, M.E.R. Shanahan, F. LavelleAnalytical and Experimental investigations of Crack Propagation in Adhesively Bonded Joints with the Mixed Mode Bending (MMB) Test Part I: Macroscopic analysis & Digital Image Correlation measurements, Theor. Appl. Fract. Mec. 74, 209–221 (2014).
65. 2014
    N. Ben Salem, J. Jumel, M.K. Budzik, M.E.R. Shanahan, F. LavelleAnalytical and Experimental investigations of Crack Propagation in Adhesively Bonded Joints with the Mixed Mode Bending (MMB) Test Part II: Investigation of cohesive stresses distribution with backface strain monitoring, Theor. Appl. Fract. Mec. 74, 222–232 (2014).
66. 2014
    M. Landowski, M.K. Budzik, K. ImielińskaWater absorption and blistering of GFRP marine laminates with nanoparticle modified coatings, J. Comp. Mat. 48(23), 2805–2813 (2014).
67. 2013
    M.K. Budzik, J. Jumel, M.E.R. Shanahan4-point beam tensile test on soft adhesive, Materials & Design 46, 134–141 (2013).
68. 2013
    J. Jumel, M.K. Budzik, N. Ben Salem, M.E.R. ShanahanInstrumented End Notched Flexure - Crack propagation and process zone monitoring. Part I: Modelling and analysis, Int. J. Solids Struct. 50, 297–309 (2013).
69. 2013
    M.K. Budzik, N. Ben Salem, J. Jumel, M.E.R. ShanahanInstrumented End Notched Flexure - Crack propagation and process zone monitoring. Part II Data reduction and experimental, Int. J. Solids Struct. 50, 310–319 (2013).
70. 2013
    J. Jumel, S. Chauffaille, M.K. Budzik, M.E.R. ShanahanViscoelastic Foundation Analysis of Single Cantilever Beam (SCB) Test Under Stationary Loading, Eur. J. Mech. A Solids 39, 170–179 (2013).
71. 2013
    N. Ben Salem, M.K. Budzik, J. Jumel, M.E.R. Shanahan, F. LavelleInvestigation of the crack front process zone in the Double Cantilever Beam test with backface strain monitoring technique, Eng. Fract. Mech. 98, 272–283 (2013).
72. 2013
    M.K. Budzik, J. Jumel, M.E.R. ShanahanAdhesive Fracture of Heterogeneous Interfaces, Phil. Mag. 93(19), 2413–2427 (2013).
73. 2013
    M. Landowski, M.K. Budzik, K. ImielińskaDynamic Mechanical behaviour of GFRP composites with SiO2 nanoparticles reinforced epoxy matrix, Adv. Mater. Sci. 13(4), 5–8 (2013). DOI: 10.2478/adms-2013-0014 DOI
74. 2012
    M. Landowski, M.K. Budzik, K. ImielińskaDegradation of Gel-Coat Layer in Glass/Polyester Laminate in Seawater Environment, Solid State Phenom. 183, 107–110 (2012).
75. 2012
    B. Mascaro, M.K. Budzik, M. Castaigns, J. Jumel, M.E.R. ShanahanEvaluation of adhesive bond Young’s modulus during crosslinking using a mechanical method and an ultrasound method, J. Phys. Conf. Ser. 353, 012006 (2012).
76. 2012
    M.K. Budzik, B. Mascaro, M. Castaigns, J. Jumel, M.E.R. ShanahanMonitoring of Crosslinking of a DGEBA-PAMAM Adhesive using Mechanical and Ultra-Sound Techniques, Int. J. Adhes. Adhes. 35, 120–128 (2012).
77. 2012
    M.K. Budzik, J. Jumel, M.E.R. ShanahanOn the crack front curvature in adhesive joints, Theor. Appl. Fract. Mec. 59, 8–20 (2012).
78. 2012
    M.K. Budzik, J. Jumel, M.E.R. ShanahanAntagonist adhesion effects due to variable surface treatment, Soft Matter, DOI: 10.1039/c2sm25180a (2012). DOI
79. 2012
    M.K. Budzik, J. Jumel, M.E.R. ShanahanImpact of interface heterogeneity on joint fracture, J. Adhesion 88(11–12), 885–902 (2012).
80. 2012
    M. Landowski, M.K. Budzik, K. ImielińskaWater sorption and blistering of GFRP laminates with varying structures, Adv. Mater. Sci. 12(4), 23–29 (2012). DOI: 10.2478/v10077-012-0013-4 DOI
81. 2011
    M.K. Budzik, J. Jumel, K. Imielińska, M.E.R. ShanahanEffect of Adhesive Compliance in the Assessment of Soft Adhesives with the Wedge Test, J. Adhes. Sci. Tech. 25, 131–149 (2011).
82. 2011
    M.K. Budzik, J. Jumel, M.E.R. ShanahanAdhesive compliance effect in mode I separation: Profilometry approach, Int. J. Adhes. Adhes. 31, 135–145 (2011).
83. 2011
    M.K. Budzik, J. Jumel, M.E.R. ShanahanFormation and growth of the crack in bonded joints under Mode I fracture: Substrate deflection at crack vicinity, J. Adhesion 87(10), 967– 988 (2011).
84. 2011
    J. Jumel, M.K. Budzik, M.E.R. ShanahanProcess zone in the Single Cantilever Beam under transverse loading, Part I: Theoretical Analysis, Theor. Appl. Fract. Mec. 56, 7–12 (2011).
85. 2011
    M.K. Budzik, J. Jumel, M.E.R. ShanahanProcess zone in the Single Cantilever Beam under transverse loading, Part II: Experimental, Theor. Appl. Fract. Mec. 56, 13–21 (2011).
86. 2011
    J. Jumel, M.K. Budzik, M.E.R. ShanahanBeam on Elastic Foundation with Anticlastic Curvature: Application to Analysis of Mode I Fracture Tests, Eng. Fract. Mech. 78(18), 3253–3269 (2011).
87. 2011
    M.K. Budzik, J. Jumel, M.E.R. ShanahanAn in-situ technique for the assessment of adhesive properties of a joint under load, Int. J. Fract. 171(2), 111–124 (2011).
88. 2011
    M. Landowski, M.K. Budzik, K. ImielińskaOn degradation of glass/polyester laminate immersed in the water, Adv. Mater. Sci. 11(1), 35–39 (2011).
89. 2011
    J. Jumel, M.K. Budzik, S. Chauffaile, M.E.R. ShanahanTwo tests for adhesive bonding long term characterization: Principles and Applications, Adv. Mater. Sci. 11(2), 44–55 (2011).
90. 2011
    M. Landowski, M.K. Budzik, K. ImielińskaEffect of manufacturing on the properties of polyester/glass fiber laminates used for construction of small yachts and boats, Materials Engineering (in Polish) 9(5), 868–872 (2011).
91. 2010
    M.K. Budzik, J. Jumel, K. Imielińska, M.E.R. ShanahanFracture energy measurements of the joint with soft bondline, Materials Engineering (in Polish) 5(177), 1366–1371 (2010).
92. 2010
    J. Tysarczyk, M.K. Budzik, J. Jumel, K. Imielińska, M.E.R. ShanahanReliable method of assessing fracture properties of asymmetric bonded joints, Adv. Mater. Sci. 10(1), 43–52 (2010).
93. 2010
    M.K. Budzik, J. Jumel, M.E.R. ShanahanFracture Energy of Bonded Joints with 2D Elastic Adhesive Layer, Adv. Mater. Sci. 10(3), 4–16 (2010).
94. 2010
    M.K. BudzikFracture tests of adhesive joints, in Modern technologies and energy conversion, ed. W. Przybylski (in Polish), Gdansk Univ. Tech., ISBN 978-83-88579-52-3 (2010). Book chapter
95. 2009
    M.K. Budzik, J. Jumel, K. Imielińska, M.E.R. ShanahanAccurate and Continuous Adhesive Fracture Energy Determination using an Instrumented Wedge Test, Int. J. Adhes. Adhes. 29, 694–701 (2009).
96. 2009
    M.K. Budzik, J. Jumel, K. Imielińska, M.E.R. ShanahanFracture in Composite/Aluminium Joints of Variable Adhesive Properties, J. Adhesion 85(10), 736–754 (2009).
97. 2009
    M.K. Budzik, J. Jumel, K. Imielińska, M.E.R. ShanahanCrack propagation in the variable adhesion properties condition, Materials Engineering (in Polish) 2(168), 118–122 (2009).
98. 2009
    M.K. Budzik, R. Pilawka, J. Jumel, K. Imielińska, M.E.R. ShanahanFracture of aluminium joints bonded with epoxy adhesive reinforced by MMT nanoparticles, Adv. Mater. Sci. 9(2), 4–11 (2009).
99. 2009
    M.K. BudzikStrain gauge based measurements of the fracture properties of adhesive joints, in Modern technologies and energy conversion, Edited by W. Przybylski (in Polish), Gdansk Univ. Tech, Gdansk, PL (2009). Book chapter
100. 2008
     M.K. Budzik, J. Jumel, K. ImielińskaDefect detection in Al/CFRP composite bonded joints using ultrasonic technique, Mechanics 2007, ISBN 978-83-88579-96-7.
101. 2008
     M.K. Budzik, J. Jumel, K. ImielińskaProperties of Al/CFRP composite adhesive bonding, Materials Engineering (in Polish) 1(161), 42–46 (2008).
102. 2008
     M.K. BudzikDefect detection in Al/CFRP composite bonded joints using ultrasonic technique, in Modern technologies and energy conversion, ed. W. Przybylski (in Polish), Gdansk Univ. Tech., ISBN 978-83-88579-22-6 (2008). Book chapter